Models - 64 Trakrane Load Chart

64 Trakrane Load Chart

(FT)

ON RAILWHEELS

ON TIRES

ON OUTRIGGERS

DIST

(FT)

OVER

END

270^o

OVER

END

OVER

SIDE

OVER

END

OVER

SIDE

3.3

3.5

4.0

5.0

6.0

4.0

50,000

44,200

30,400

25,800

18,000

16,000

14,000

9,000

7,000

5,000

24,000

21,000

18,000

15,000

12,000

9,000

18,000

16,000

14,000

8,000

7,000

6,000

50,000

44,000

33,000

22,000

50,000

34,000

23,000

12,000

3.0

4.0

5.0

6.0

7.0

50,000

43,000

32,000

21,000

10,000

8,000

6,000

4,000

2,000

15,000

12,000

10,000

8,000

6,000

10,000

8,000

6,000

5,000

4,000

50,000

43,000

31,000

23,000

18,000

50,000

32,000

23,000

18,000

14,000

3.0

4.0

5.0

6.0

7.0

8.0

50,000

40,000

30,000

20,000

18,000

15,000

6,500

5,400

4,300

3,300

2,200

1,000

17,000

12,000

9,000

7,000

5,000

4,000

12,000

9,000

8,000

6,000

5,000

4,000

50,000

42,000

29,000

22,000

18,000

15,000

50,000

24,000

23,000

18,000

14,200

11,700

17,000

11,000

8,000

6,000

5,000

4,000

3,000

2,000

13,000

6,000

5,000

4,000

3,000

2,500

2,000

1,000

50,000

42,100

29,700

22,400

17,000

14,000

12,000

10,000

50,000

27,000

23,000

17,000

13,000

11,000

8,000

6,000

50,000

42,700

29,800

22,300

17,700

14,800

12,400

10,600

7,800

50,000

34,400

23,100

17,600

12,000

11,400

8,100

6,500

5,000

On Railwheels Working Area	These lines show the work areas where the above rated loads apply. WARNING *270° Lifts are with boom angles of 10° or less. Operating Boom above 70° may result in stability loss. 1. Distances parallel to the rear of the carrier from the railroad track centerline to the load center line. This keeps the load inside a line drawn from the center of rotation touching the rear inside edge of the rear railwheel.
On Tires Working Area	These lines show the work areas where the above rated loads apply.
On Outriggers Working Area	These lines show the work areas where the above rated loads apply. Outrigger Lifts are with Outrigger beams fully extended and floats set to sully support and level the machine (Tires off the supporting surface) Structural support under floats may be necessary in rough terrain or to spread the load over a larger bearing surface.

1.	All operators and support personnel shall read and fully understand manufacturer's manual, the latest applicable American National Standards Institute (ANSI) Safety Standards for Cranes and any applicable federal, state and local safety regulations before operating machine. Crane and load rating comply with ANSI and Power Crane & Shovel Association ( PCSA) standards.
2.	High gantry assembly in the raised position shall be used when lifting loads with 60' of boom or longer.
3.	Shaded load ratings are based on machine's structural strengths. All other ratings do not exceed 75% of lipping load "ON TIRES" or 25% "ON OUTRIGGERS" with machine stable and level on firm ground within 1% grade "ON RAILWHEELS".
4.	DO NOT EXCEED crane loading ratings. When load radius or boom angle is between listed values, use the smaller load rating. DO NOT ATTEMPT TO TIP MACHINE TO DETERMINE ALLOWABLE LOADS.
5.	Weight of hook blocks, buckets, and all other load handling devices are not accounted for in the load chart. Load handling devices are part of a load.
6.	Reduce ratings appropriately for wind conditions. CAUTION IN WIND OVER 3 MPH CEASE OPERATION; POSITION BOOM AWAY FROM THE WIND AND LOWER BOOM BELOW 65°. IN WIND OVER 50 MPH LOWER BOOM TO GROUND OR SECURE IN POSITION. Reduce ratings appropriately for speed of operation, soft or uneven supporting surface, etc.
7.	Load ratings apply to this machine ONLY as originally manufactured and equipped. Unspecified modifications or optional equipment may reduce load capacity. Please consult *LITTLE GIANT* before modifications or or use of optional equipment not covered on this chart.
8.	These load ratings are for lift service only. Consult and adhere to appropriate load ratings charts for other applications (clamshell, dragline, magnet, etc.)
9.	Pick and carry load ratings are limited to 70% of "On Railwheels - Over Road" load ratings when on call and 80% of "On Tires - Over Road" lifts when on timers. Pick and carry operations shall be made using 80% of boom or less at the lowest possible boom angle and the longest allowable load radius. Load shall be restrained from swinging and shall be positioned close to the ground as possible over the rear along the carriers lengthwise centerline. DO NOT exceed 3 mph (8 km/h) travel speed using smooth starts and slops. Other crane operations shall not be permitted when transporting a load

RECOMMENDATIONS: Use five parts of lime for maximum lifts with precise control. ³/₈" = 8 x 10 Extra Improved Plowsleet WAC Wire rope

PARTS OF LINE	1	2	3	4	5
MAX HOOK LOAD	11,500	23,000	22,000	48,000	60,000

Back

Due to continuing efforts to improve our products, literature is subject to change without notice. Check back for frequent updates!